OE 2052Z1 products
CITROËN: 2052Z1
CITROËN: 2052.Z1
CITROËN: 2052-Z1
CITROËN: 2052 Z1
CITROËN/PEUGEOT: 2052.Z1
CITROËN/PEUGEOT: 2052 Z1
DS: 2052Z1
DS: 2052.Z1
DS: 2052 Z1
DS: 2052-Z1
PEUGEOT: 2052Z1
PEUGEOT: 2052.Z1
PEUGEOT: 2052-Z1
PEUGEOT: 2052 Z1
OE number or original number means the number of the whole component or part of it installed on the vehicle on the production line by the car manufacturer. The meaning of the OE number is equivalent to "Genuine Number"
| Multi-piece | two-piece |
| Number of Teeth | 26 |
| Hub Profile | 20x21.5 |
| Supplementary Article/Supplementary Info | without central slave cylinder, with clutch pressure plate, with synthetic grease |
| Adjustment | without automatic adjustment |
| Supplementary Article/Supplementary Info 2 | with clutch disc |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Friction Lining Outer Diameter 1 | 235mm |
| More information » | |
| Outer Diameter | 240mm |
| Number of Teeth | 26 |
| Multi-piece | two-piece |
| Supplementary Article/Supplementary Info | with synthetic grease |
| Clutch | Replacement for self-adjusting clutch pressure plate |
| Observe service information | |
| Guarantee | 3 years guarantee |
| More information » | |
$132.90
$156.30
-15%
| Ø | 235mm |
| Number of Teeth | 26 |
| only available in set | |
| Supplementary Article/Supplementary Info 2 | without clutch release bearing |
| Warranty | 3 years warranty |
| SVHC | No information available, please contact the manufacturer! |
| Multi-piece | three-piece |
| Number of Teeth | 26 |
| Hub Profile | 20x21.5 |
| Supplementary Article/Supplementary Info | with central slave cylinder, with clutch pressure plate, with synthetic grease |
| Adjustment | without automatic adjustment |
| Supplementary Article/Supplementary Info 2 | with clutch disc |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Friction Lining Outer Diameter 1 | 235mm |
| More information » | |
| New Part | |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Number of Teeth | 26 |
| Hub Profile | 21, 56 x 20, 05 |
| Supplementary Article/Supplementary Info | without central slave cylinder |
| Clutch | for vehicles with push type clutch |
| for flywheel manufacturer | VALEO |
| Supplementary Article/Supplementary Info 2 | Special tools for mounting not necessary |
| Weight | 5.35kg |
| More information » | |
| Ø | 235mm |
| Number of Teeth | 26 |
| only available in set | |
| Supplementary Article/Supplementary Info 2 | without clutch release bearing |
| Warranty | 3 years warranty |
| SVHC | No information available, please contact the manufacturer! |
| Outer Diameter | 236mm |
| Number of Teeth | 26 |
| Multi-piece | three-piece |
| Supplementary Article/Supplementary Info | with synthetic grease, with central slave cylinder |
| Observe service information | |
| Guarantee | 3 years guarantee |
$180.90
$212.80
-15%
| Multi-piece | three-piece |
| Number of Teeth | 26 |
| Hub Profile | 20x21.5 |
| Supplementary Article/Supplementary Info | with central slave cylinder, with clutch pressure plate, with synthetic grease |
| Adjustment | without automatic adjustment |
| Supplementary Article/Supplementary Info 2 | with clutch disc |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Friction Lining Outer Diameter 1 | 235mm |
| More information » | |
| Ø | 235mm |
| Hub Profile | 21, 5 x 26 |
| Supplementary Article/Supplementary Info | with clutch pressure plate |
| Supplementary Article/Supplementary Info 2 | with clutch disc |
| Ø | 240mm |
| Adjustment | with automatic adjustment |
| SVHC | No SVHC present! |
$250.80
$295.10
-16%
| New Part | |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Number of Teeth | 26 |
| Hub Profile | 21, 56 x 20, 05 |
| Supplementary Article/Supplementary Info | with central slave cylinder |
| Number of mounting bores at central slave cylinder | 3 |
| Bore Ø | 24mm |
| Material | Plastic |
| Supplementary Article/Supplementary Info 2 | with sensor, Special tools for mounting not necessary |
| Clutch | for vehicles with push type clutch |
| Weight | 6.5kg |
| More information » | |
| New Part | |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Number of Teeth | 26 |
| Hub Profile | 21, 56 x 20, 05 |
| Supplementary Article/Supplementary Info | with central slave cylinder |
| Number of mounting bores at central slave cylinder | 3 |
| Bore Ø | 24mm |
| Material | Plastic |
| Supplementary Article/Supplementary Info 2 | without sensor, Special tools for mounting not necessary |
| Clutch | for vehicles with push type clutch |
| Weight | 6.275kg |
| More information » | |
| Ø | 240mm |
| Supplementary Article/Supplementary Info | with central slave cylinder |
| Adjustment | with automatic adjustment |
| SVHC | No SVHC present! |
$306.00
$359.90
-15%
| Ø | 240mm |
| Supplementary Article/Supplementary Info | with central slave cylinder |
| Adjustment | with automatic adjustment |
| SVHC | No SVHC present! |
$317.50
$373.60
-16%
| Multi-piece | four-piece |
| Number of Teeth | 26 |
| Hub Profile | 20x21.5 |
| Supplementary Article/Supplementary Info | with central slave cylinder, with clutch pressure plate, with dual-mass flywheel, with synthetic grease |
| Adjustment | without automatic adjustment |
| Supplementary Article/Supplementary Info 2 | with clutch disc, with screw set |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Friction Lining Outer Diameter 1 | 235mm |
| More information » | |
| New Part | |
| Supplementary Article/Supplementary Info | with dual-mass flywheel, with flywheel screws, with pressure plate screws, with central slave cylinder |
| Number of mounting bores | 6 |
| Tightening Torque | 30Nm |
| Tightening degree | 90° |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Number of Teeth | 26 |
| Bore Ø | 24mm |
| Material | Plastic |
| Supplementary Article/Supplementary Info 2 | without sensor, Special tools for mounting not necessary |
| Mounting Type | Clipped |
| Weight | 19.53kg |
| More information » | |
| New Part | |
| Supplementary Article/Supplementary Info | with single-mass flywheel, with central slave cylinder |
| Clutch | Conversion from dual-mass flywheel to single-mass flywheel, for vehicles with push type clutch |
| Tightening Torque | 60Nm |
| Clutch Pressure Plate Outer Diameter | 240mm |
| Number of Teeth | 26 |
| Hub Profile | 22 x 20 |
| Number of mounting bores at central slave cylinder | 3 |
| Bore Ø | 24mm |
| Material | Plastic |
| Supplementary Article/Supplementary Info 2 | Special tools for mounting not necessary |
| Weight | 17.22kg |
| More information » | |
| Multi-piece | four-piece |
| Number of Teeth | 26 |
| Hub Profile | 20x21.5 |
| Supplementary Article/Supplementary Info | with central slave cylinder, with clutch pressure plate, with dual-mass flywheel, with synthetic grease |
| Adjustment | without automatic adjustment |
| Supplementary Article/Supplementary Info 2 | with clutch disc, with screw set |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Friction Lining Outer Diameter 1 | 235mm |
| More information » | |
| New Part | |
| only to be used within set | |
| Supplementary Article/Supplementary Info | with dual-mass flywheel, with flywheel screws, with pressure plate screws, with central slave cylinder |
| Number of mounting bores | 6 |
| Tightening Torque | 60Nm |
| Clutch Pressure Plate Outer Diameter | 235mm |
| Number of Teeth | 26 |
| Number of mounting bores at central slave cylinder | 3 |
| Bore Ø | 24mm |
| Material | Plastic |
| Supplementary Article/Supplementary Info 2 | with sensor |
| Weight | 18.26kg |
| More information » | |
| Ø | 240mm |
| Number of Teeth | 21 |
| Mounting Type | not pre-assembled |
| Supplementary Article/Supplementary Info | with dual-mass flywheel, with clutch pressure plate, with central slave cylinder |
| Supplementary Article/Supplementary Info 2 | with clutch disc, with screw set |
| Warranty | 3 years warranty |
| SVHC | No information available, please contact the manufacturer! |
| More information » | |
The data shown here, especially the complete database of car spare parts, may not be copied. It is strictly prohibited to duplicate the data and database and distribute the same, and/or instruct third parties to engage in such activities, without prior consent from TecAlliance. Any use of content in a manner not expressly authorized constitutes copyright infringement and violators will be prosecuted. 