device brake- and Hüdraulikavedeliku for changing, pneumatic

device brake- and Hüdraulikavedeliku for changing, pneumatic

professional device brake fluid and hüdrovedeliku asendamiseks hydraulic clutch juhtimissüsteemis manuaalkäigukastis. device Works CLOSED ahelas algrõhuga up to 3 BAR . due to to it on brake fluid changing peaaegu in all systems easy and effective without tarbetu õhutamiseta, even ABS-each . special adapters to a different brake fluid paisupaakidele suitable for European, Japan and American cars, allow to connect survepaagi new vedelikuga and to remove old liquid üksikutelt rattasadulatelt.

working pressure 0,69–2,76 BAR (10–40 PSI)
Õhuühendus ¼”
tank capacity 5 l
Measurement range 0–10 BAR (0–140 PSI)
cable length 3 m
sizes Ø 28/21/46 cm
tank capacity 1,2 l
weight 8,9 kg

preparation
1. car peaks be for lifter peal well ventilated place.
2. Stop engine.
3. Kinnitage fittings pidurisilindrite mounting.
4. switch Air compressor in and Place the hose Device lähedale
(kompressoril peaks be niiskusfilter)
5. pour machine into the tank värsket brake fluids.
for brakes venting and new liquid addition
1. Place the vedelikuvahetusseade car kõrvale.
2. remove brake fluid reservuaari cap and asendage this supplied with cap.
3. Valige adapters komplektist this, which suitable for most better paisupaagiga.
Mõnel juhul Can be used universaalset covers (E1, F1 or F2), kui other adapters it no tee
sobima. Kinnitage cover with adapter kaasasolevate montaažikaablite and elementidega.
4. Kinnitage reservuaari lid.
5. Ühendage hose (16) quick connector (15) laienduse temporary sockets.
tank. Check, et kuulkraan (9) oleks CLOSED (hose on side).
6. Alustage change paisupaagist most kaugemal asuvast rattast.
Ühendage õhutusvoolikud car mõlemal on side olevate pidurisadulatega. Place the
äravoolutorud used brake fluid reservuaarides. Vabastage õhutusava.
7. Ühendage device pneumaatilise system through kiirühenduse (8).
device.
8. set up valve (9) to the position ON (vertical).
9. pull rõhureguleerimisventiili (10) nuppu and vaadake manomeetrit
(19), reguleerige pressure with button in the range of 0,7–2,7 BAR (20–40 PSI).
Note. don't exceed pressure 2,76 BAR 40 psi, beacuse this may masinat and voolikuid to damage.
10. open slowly peasilindri hose (16) kuulkraan (9).
this alustab new liquid väljapressimist and old pudelitesse tõmbamist.
Check all connections leaks in a ratio. leak korral stop procedure.
11. push quickly piduripedaali and vabastage this slowly liquid ülekandmise ajal.
Make it procedure many times.
12. Kui bottles on full, lõpetage procedure and tühjendage pudelitest old fluid.
13. repeat procedure eesmiste pidurisadulatega.
14. after liquid assembly completion Turn peasilindri kuulkraan (9) to the position OFF
(külgsuunas) and remove hose (16) tank kaanelt.
liquid addition ABS-each sõidukitesse
1. Järgige all ülaltoodud samme following eranditega.
2. Vabastage at once only one clamp tühjenduskruvi and let this tühjaks.
3. after liquid change switch engine off.
4. Visake used vedelikupudelid minema.
5. repeat the same with other cylinders puhul.

after liquid change
1. Place the originaalpaagi lid backward.
2. Ühendage air hose open reservuaari kiirühenduse liitmiku (8) küljest.
3. open reservuaari air väljalaskeklapp (9) and pull for release kaitseklappi (12).
pressure reservuaarist.
4. pour bottles content utiliseerimiseks used brake fluid mahutisse.
attention: before with car sõitmist push korduvalt piduripedaali, up to this significantly langeb.
Check terminals tihedust. then test pidureid low with speed before normaalset sõitmist.
conditioning
Note. before Device maintenance be sure that, et this pole under pressure.
1. wipe off voolanud brake fluid.
2. wipe device soft with cloth.
3. to keep in dry and puhtas place.

User's Guide

Delivery method